Forum Navigation
Post History: a_t_j
Yes it is the Edelbrock system and the sticker says USA but I'll bet there are more than a few …In: Intermittently keeps restarting fuel and prime on initial "key on"
8 months ago
No I went with the pro flo 4 and love it. A few little things with it as well but completely resolve …In: Intermittently keeps restarting fuel and prime on initial "key on"
8 months ago
New update I felt I should post rather than just go silent.
I am sorry to say that I just could n …In: Intermittently keeps restarting fuel and prime on initial "key on"
8 months ago
Update: I am happy to report that the new ECU seems to have fixed all the faults and issues I was ha …In: Intermittently keeps restarting fuel and prime on initial "key on"
3 years ago
I hear ya its very frustrating, especially if your installing for a customer !! I'm giving my F …In: Intermittently keeps restarting fuel and prime on initial "key on"
3 years ago
Well I got my new replacement ECU and installed it. Wasn't a terribly hard thing to do.
So f …In: Intermittently keeps restarting fuel and prime on initial "key on"
3 years ago
So I did some playing around and using ECU programmer reloaded the hex file (which I have done befor …In: Intermittently keeps restarting fuel and prime on initial "key on"
3 years ago
Just seen a topic/post by DerekO which had the same issue as I'm seeing.
"Key On cyclin …In: Intermittently keeps restarting fuel and prime on initial "key on"
3 years ago
DerekO
Just seen this after I posted a new topic.
My 30004 is now having the exact same issues …In: Key On cycling and hard starting
3 years ago
Been having a weird problem with my 30004 lately. Sometimes, not always, when I turn the key on (12V …In: Intermittently keeps restarting fuel and prime on initial "key on"
3 years ago
No I could not adjust it out for some reason. Tried playing with all kinds of settings such as loop …In: Anyone using an MSD ready to run with Fitech ?
3 years ago
Did some experimenting with my ignition setup...
Setup the Fitech to VR coil for ignition control …In: Anyone using an MSD ready to run with Fitech ?
3 years ago
Yes like you say I thought about retarding the distributor some more and re-phasing the rotor etc. H …In: Anyone using an MSD ready to run with Fitech ?
4 years ago
Sure in my case it seems to be a bit of a trade-off here.
I am leaning towards just using my MSD …In: Anyone using an MSD ready to run with Fitech ?
4 years ago
Well I tried going back to my old duraspark ignition module and distributor and found roughly the sa …In: Anyone using an MSD ready to run with Fitech ?
4 years ago
Thanks for that I hooked the blue wire to the tach output on the MSD and also tried wiring to the ne …In: Anyone using an MSD ready to run with Fitech ?
4 years ago
Curious if anyone has a ready to run setup with their fitech and if they have experienced any idle s …In: Anyone using an MSD ready to run with Fitech ?
4 years ago
Hi all,
Just wanted to post this to get some feedback from the more experienced on this forum to …In: Adjusting Cam Fuel Tables ?
4 years ago
Update:
Today I fired it up to see and surprisingly the O2 reading and trim were working again an …In: P0130 and AFR stuck at 14.7
4 years ago
Ok I'm still having this problem with the O2 sensor reading locking up or failing. I put in a b …In: P0130 and AFR stuck at 14.7
4 years ago
I realize this post is a year old but I ran into a similar problem recently with my O2 sensor on my …In: P0130 and AFR stuck at 14.7
4 years ago