Forum Navigation
Post History: taylorteamracing
just fyi I ran a msd 6a,l and now a summit box, a 3 step, blaster 2 coil, Taylor 8.8 wires, billet d …In: FiTech with MSD ignition
5 years ago
okay this motor don't like the 17104 plugs I put a new set of yhe 3924 autolites in and runs al …In: dual power adder with hyperfuel stalls runs rough
5 years ago
fitech recommends 110 lobe center or more, on there website is starting points for the cam selection …In: Cam Selection
5 years ago
i also removed the autolite double platinum plugs and installed the ngk 6596 it is a cooler plug tha …In: dual power adder with hyperfuel stalls runs rough
5 years ago
5 years ago
okay i installed the new eBay o2s and the car fired up and ran thank god i then took it out on a 3 m …In: dual power adder with hyperfuel stalls runs rough
5 years ago
okay i received the new o2 sensor i will install it tomorrow, there is 0 leaks in the exhaust system …In: dual power adder with hyperfuel stalls runs rough
5 years ago
manifold vacuum, and the different cam settings sets up different fuel trim and delivery table as a …In: Cam selection in initial set up
5 years ago
I ordered a 17014 sensor off of egay if it fixes it ill go get a bosh and keep the other as a spare, …In: fuel dumping
5 years ago
ill check it out later this afternoon may just get a new one there cheap easy to replace there is a …In: fuel dumping
5 years ago
I just checked I am getting return to the tank and my running psi is 77 here is the odd part my targ …In: fuel dumping
5 years ago
just went and checked my running fuel pressure is 77 psi I am in fact getting return fuel to the tan …In: fuel dumping
5 years ago
also the only thing controlling my hyper fuel is the 12v power supply from the fitech no vac goes to …In: fuel dumping
5 years ago
I have two fuel pressure gauges coming off of the hyper fuel to each of the throttle bodies I checke …In: fuel dumping
5 years ago
is there anything that controls the fuel pressure so it dose not over power the injectors and displa …In: fuel dumping
5 years ago
okay I installed a NEW ignition box, 3 step retard, blaster 2 coil, msd distributor pick up coil, ne …In: dual power adder with hyperfuel stalls runs rough
5 years ago
yup went out today started the car and it ran great,,,,,,,, pffft lol so I let it get to normal tem …In: Fuel Pump Problems
5 years ago
I had a similar issue not sure what is yet but it ran on test drive for about 45 min and sputtered l …In: Fuel Pump Problems
5 years ago
I have ha a heck of a time getting my temperature under control and I finally have it running betwe …In: dual power adder with hyperfuel stalls runs rough
5 years ago
I have about the same cam spec on a big block and I notice mine ran better on cam 2 on fitech websit …In: Cam selection in initial set up
5 years ago
Austin will say the same thing I am going to tell you GROUNDS are crucial as I have found out on my …In: FINAL INSTALL
5 years ago
my big block 545 has a 871 on it I set all afr targets to 12;8;1 and I have ignition timing locked …In: AFR and Ignition questions...
5 years ago
ringing ???? does it sound like a bell or like a dragging dinging sound that to me sounds like deton …In: Rpm noise problem
5 years ago
if anyone is running big cubic inches 460 454 396 390 557 545 600 ect and your build needs 32 or gre …In: ignition wiring to avoid hard starts
5 years ago
to answer your other question I un hooked my batteries and pulled all the fitech fuses reinstalled e …In: Where do I start...
5 years ago
not sure I have the dual power adder 1200 hp sys ill un hook my battery tomarrow and seeIn: Where do I start...
5 years ago
sounds like you need a controller and if you cant get a replacement controller cable you will be nee …In: Where do I start...
5 years ago
have you checked for a vacuum leak around the intake and throttle body gasket, what is the lobe sepa …In: Starting over , need help
5 years ago
a locked dist that advances.. interesting okay greatIn: Using Vacuum Advance With FiTech Controlled Timing
5 years ago
I have 1 tip for you when you set you initial 14 degrees; before you put the timing tape on and line …In: Using Vacuum Advance With FiTech Controlled Timing
5 years ago
if you need a temp sensor extension fitech tech dept. referred me to http://www.casperselectronics.c …In: coolant temp sensor extention kit
5 years ago
try casper electronics fitech tech dept sent me there for a cool at temp sensor connectors kit to ma …In: Oxygen Sensor Extension Harness
5 years ago
you know what mine did that in a ford racing billet distributor a while back I put in a msd moduleIn: RPM is all over during engine cranking
5 years ago
also shield all wires on that speedhut gps speedo there notorious for interference I used to have th …In: RPM is all over during engine cranking
5 years ago
can I interject ,,,, when it is hot and you are starting to crank it does it turn over slow or fast …In: Warm start issue / FiTech 30020
5 years ago
if you back fired you may have blown out the back of the blower bas gasket known problem with super …In: backfire through throttle bodies
5 years ago
no I don't recommend using the fitech for ignition control, boosted motors are a PITA to get tu …In: all together
5 years ago
if you select the hyper fuel command center you must use two separate 12 volt power supply to the e …In: HYPER FUEL
5 years ago
awesome just keep tweaking it here and there sound like you got it by the tail good luckIn: 557 BBF Timing go efi 1200
5 years ago
Also try increasing timing to 20 all in at 2000rpm @ 36 it will remove some heat
Probably around …In: 557 BBF Timing go efi 1200
5 years ago
if you are having heating or over heating issues especially in big inch motors turbo or forced induc …In: 557 BBF Timing go efi 1200
5 years ago
when I spoke to the fitech guys when I was buying and selecting my system I had a "big muther …In: 557 BBF Timing go efi 1200
5 years ago
just my 2cents worth but when you set ALL IN timing you should be setting it to true tdc I have a 5 …In: 557 BBF Timing go efi 1200
5 years ago
how ya get a data log I have seen that in the hand held just don't know how to record and trans …In: blown 871 545 ci dual power adder system wierd cruse miss or stumble
5 years ago
not sure my plugs was a dark tanish color with some black carbon the burn looked okay to me, t reduc …In: blown 871 545 ci dual power adder system wierd cruse miss or stumble
5 years ago
I had the car out the other day and I notice it when it was warm between 200 and 220 degrees it acts …In: blown 871 545 ci dual power adder system wierd cruse miss or stumble
5 years ago