Forum Navigation
Post History: taylorteamracing
there is a delco pig tail kit you can make it as long as you need just just search online for fitech …In: O2 Harness extension
5 years ago
i could have flipped it over and read the directions (f.o.r.d) .,.,.,.,.,.,.,.,.,.,., next weekend …In: running hot 545 blown 871 dual power adder
5 years ago
couldn't find my old thread I think this belongs here,, I have a 460 stroked to 545 cubic inche …In: running hot 545 blown 871 dual power adder
5 years ago
5 years ago
i figured out what happen when you adjust you iac steps or warm idle it turn the idle screw out to f …In: froze up throttle body
5 years ago
I went for a test drive today and two things happened first I have the 1200 hp power adder dual syst …In: froze up throttle body
5 years ago
was you able to ask at sema about adjusting the throttle spring pressure especially for the dual pow …In: throttle pressure
5 years ago
don't know exactly what to change for that but I did just get back from the maiden voyage the o …In: cold start idle hunting
5 years ago
to start the 545 871 blown big block I have to cycle the key 3 time with throttle crack to get fuel …In: cold start idle hunting
5 years ago
well fitech sent me two new pumps but..... I installed two independent 60 amp relays and increased t …In: wires gettin HOT HOT HOT
5 years ago
well I spoke to fitech today and they said those pumps are supposed to pull 12 amps ? that being sai …In: wires gettin HOT HOT HOT
6 years ago
well I am running the hyper fuel setup with the power adder dual fitech on a 871 blown 545 ci engine …In: wires gettin HOT HOT HOT
6 years ago
14 to 13.5 I would think is a bit lean for a blower motorIn: 545 stroked 460 with 871 blower now runs here are my settings
6 years ago
sry didn't know about the power adder section lol remember blower application are all on a diff …In: 545 stroked 460 with 871 blower now runs here are my settings
6 years ago
yes fitech site recommends actual 11:5:1 to I believe 12: 8,, rich at idle is okay to a point for b …In: 545 stroked 460 with 871 blower now runs here are my settings
6 years ago
one other thing is there any way to adjust the throttle tension I am using the dual power adder on a …In: its alive but have issues
6 years ago
okay once upon a time ,,,, I had a overheating issue I just installed a blue water restrictor from m …In: its alive but have issues
6 years ago
okay I changed the coolant temp sensor with a AutoZone SU 203 my equus gauge and the fitech are with …In: fan 2 wire
6 years ago
yes its learning and most initial reading are where there supposed to be my idle is 1000 it bounces …In: fan 2 wire
6 years ago
okay I solved the fan 1 wire issue it was one of those new bad relays it takes twice as long now wit …In: fan 2 wire
6 years ago
well it does run and run well so far search you tube, "custom 500 alive" the yellow fan wi …In: fan 2 wire
6 years ago
well I remember the fan 1 wire is a ground if I am to understand correctly, it provides a ground fo …In: fan 2 wire
6 years ago
can the fan 2 wire be used to run 2 fans or a second high speed fan, I wired the fan 1 to a relay as …In: fan 2 wire
6 years ago
backfiring small block on a intake change sounds like a timing issue,, was the fitech running the ti …In: changed intake manifold now all kind of problems.
6 years ago
okay after reading and running the motor a few times I finally have it where it starts like a new ca …In: 545 stroked 460 with 871 blower now runs here are my settings
6 years ago
no its blower related.. lol but the fitech isn't turning the fan on either on fan 1 my current …In: its alive but have issues
6 years ago
I will half to run it again to get the IAC steps, no I didn't get it to stay cool it want to ke …In: its alive but have issues
6 years ago
its a 545 stroker with a 871 blower everything is new im running the fitech dual power adder 1200hp …In: its alive but have issues
6 years ago
I have seen this before in other applications and found it to be what is referred to as voltage drop …In: Battery voltage on handheld off
6 years ago
lol well I pressure checked my fuel system and all the fitech (blsck fittings) fittings are leaking …In: fittings fittings fittings
6 years ago
outstanding, question asked and problem solved ,, glad I asked because I did have it initially wired …In: G-Surge duel pump resivior wiring
6 years ago
yes I added scarbird front disc and put a 8.8 cobra axle in the back with a mini spool 411 . I chang …In: new to fitech ,, my build
6 years ago
I am running the fitech dual 1200 hp power adder with the g-surge dual pump reservoir,, one set of i …In: G-Surge duel pump resivior wiring
6 years ago
I am using the fitech dual pump g-surge and I have it wired to the fitech .. no relay and my 7 psi p …In: Before You Crank
6 years ago
6 years ago
I have just completed the fitech dual 1200hp setup with the g-surge dual pumps is there any setting …In: Before You Crank
6 years ago
just completed the install all need is trans fluid , fix a leaky water neck, and wire the fuel gauge …In: 545 ci 1967 galaxie dual 1200hp power adder
6 years ago
from my 30 plus years of dealing with and building small blocks supercharged and blown check your pl …In: Ignition miss at idle with timing control
6 years ago
yes I have two Holley 7 psi below the fuel cell one is a back up it will feed the g surge, I am runn …In: all together
6 years ago
I have my motor built and in the car, it is a 460 block bored, scat stroker 545 CI, it has a magnum …In: all together
6 years ago