Forum Navigation
Post History: taylorteamracing
make sure your rpm signal wire is shielded and twist wind the distributor pickup signal wires, get i …In: all together
2 years ago
o2s mine did that and the o2s went bad i swapped it with a audi tt 99-02 runs great nowIn: not starting cold
3 years ago
what most people miss is if the fans are running with the key off unless you are running a electric …In: cooling fans stay on key off,
3 years ago
something interesting happend now the motor rolls over like amonster truck enging romp ... romp ... …In: cubic inch displacment setting
3 years ago
this may seem silly but there is a rpm limiter in the pro tunning and set up i think its default is …In: Problem
3 years ago
i kept mine simple i just used a aftermarket adjustable fan controler and did not use the fan 1 or f …In: cooling fans stay on key off,
3 years ago
there has been allot of discustion on what people need to set the displacement at when using blowers …In: cubic inch displacment setting
3 years ago
thats a good question on the line size obviously you would need to buy the correct -10 fittings to s …In: Fuel supply question
3 years ago
unless admin can chime in i believe this is a dead thread there was a bunch of talk on this about 2 …In: Online Fitech Course
3 years ago
I run a billet locked distributor at 38 deg, a msd 6al a msd start retard, and a 3 step timing retar …In: Anyone using an MSD ready to run with Fitech ?
3 years ago
where is the temp sensor located, you will want it as close to the return to the radiator or as clos …In: Coolant Temp Sensor adjustment
4 years ago
my dual power adder did kinda the same thing till it just stopped running all together i bought a o2 …In: converting MSD ready to run to 2 wire
4 years ago
it sounds like a serious vac leak, also check and re-check ALL your grounds, what size cam are you r …In: Secondary Adjustment
4 years ago
okay i found the problem and i don't think fitech r and d is aware of this catastrophic problem …In: handheld not displaying gauges
4 years ago
i backed the car out about 4 days ago from the garage and everything was good, I went back to the ca …In: handheld not displaying gauges
4 years ago
the car is one of 20k built as a 62b build, the motor is a 460 stroked to 545 with a don Hampton 871 …In: 67 custom 500 blown 545 all done
4 years ago
o2s may be bad I have the power adder on a blown 545 and mine did that I ordered one off of ebay for …In: Rear 4 spark plugs gas soaked
4 years ago
mine needs primed 3 times but I am running a 871 blower with the power adder system and I have 2 100 …In: prime 5 to six times before start
4 years ago
my prob ended up being a o2s but I will put a ground on like that this system loves grounds.In: Fuel Pump Problems
4 years ago
.35 and the over heat and running hot was solved by a afco cooling systems older tech, he told me to …In: dual power adder with hyperfuel stalls runs rough
4 years ago
yes getting mine tuned right was b e a r I ended up not using the fitech timing, I used a msd 6al a …In: Online Fitech Course
4 years ago
well you will half to start from scratch again when you put the blower back on,, blowers dramaticall …In: another newbe to fitech
4 years ago
I have some info on my 871 blown dual power adder system with the hyper fuel system when you are rea …In: Online Fitech Course
4 years ago
looking at you afr you appear to be lean more than rich your target is 14 and you appear to be fluct …In: another newbe to fitech
4 years ago
a bit of info on the o2s ,, mine failed after about 10 hrs and I researched the o2s and found a BMW/ …In: Online Fitech Course
4 years ago
I advanced the timing more and kept the 3924 plugs in re did the gap and I also leaned target afr to …In: dual power adder with hyperfuel stalls runs rough
4 years ago
4 years ago
if it starts after 5 key cycles that would suggest to me ,,
not enough fuel
serious …In: Won't start after warmed and parked
4 years ago
mine has the hyper fuel with a return back to the cell, and before I fixed my overheat I would get u …In: Won't start after warmed and parked
4 years ago
my afr seems steady, engine is very responsive, this takes place from a cruse rpm of 2200 I hit it : …In: dual power adder stumble
4 years ago
I have a dual 1200 power adder sys with the hyper fuel, the only issue I have is when you press the …In: dual power adder stumble
4 years ago
try cycle the key 3 to 4 times before you crank it this will tell you if your prime is set to lowIn: Won't start after warmed and parked
4 years ago
does it start any better or worse with throttle cracked
how much timing is it loping ov …In: Won't start after warmed and parked
4 years ago
I switched to the Delco and now my equis gauge and my hand held are fairly accurate with each other …In: Coolant Temp Sensor adjustment
4 years ago
I am going to to look at it long and hard and see what I think will work this week ill report backIn: Secondary Adjustment
4 years ago
4 years ago
no adjust off of primary throttle body, secondary is just a slave, now is the cam according to the s …In: Newbie and First Data Log
4 years ago
i am running the 2x4 power adder on a blown 545 my iac is between 4 and 10, I am on cam 2 with a 230 …In: Newbie and First Data Log
4 years ago
the other issue I have is I have the dual power adder and the throttle pressure is like 50 pounds lo …In: Secondary Adjustment
4 years ago
I would like to know that myself why cant it be set up just like a mechanical carb you press the ped …In: Secondary Adjustment
4 years ago
fitech recommends a IAC setting of below 10 steps once the motor hits 160 degrees' or so turn i …In: Won't start after warmed and parked
4 years ago
where exactly is the 02 located,, it should be about 2-3 inches from the header flange in the header …In: afr goes to 16 - 17 under acceleration can not keep close to afr target
4 years ago
I changed to the delco and everything reads evenly, your other issue about your plugs check or chang …In: Temp Sensor
4 years ago
well your iac is high should be 10 or less turn idle screw down and set target idle at 900 rpm and s …In: Help to fine tune my system.
4 years ago
turn on prime shot set it at half nominal value, use cam setting 3, run 36 total advance, when cold …In: Won't start after warmed and parked
4 years ago
I have had my fitech for a 1 1/2 years it is the 1200 power adder with the hyperfuel sys on a 545 87 …In: Is Fitech junk?
4 years ago
i half to do the same on a dual power adder system with a 871 blower crack them about a 1/8 fires ri …In: Cold start
4 years ago