Forum Navigation
Post History: Austin DeHaas
We need to see AFR learn. It will be the line below AFR Trim. Plus Coolant Temp must be over 170 b …In: Plugs black. Exhaust tips black. Poor mileage. Some dark smoke
3 years ago
What does the AFR, AFR trim and AFR learn say when it is running rich?In: Plugs black. Exhaust tips black. Poor mileage. Some dark smoke
3 years ago
Charge the battery.
If it will run on starting fluid then you know timing and ignition is working …In: Wants to start.... yet will not!
3 years ago
3 years ago
1. Would like to see the voltage stay over 11 during crank. Rpm will read with low voltage.
2. I …In: Wants to start.... yet will not!
3 years ago
3 years ago
https://dennisroadautomotive.com/news/shop-news/40-store-news/1035-what-does-the-pcv-system-do--why- …In: What about pcv, vacuum leak?
3 years ago
Are you positive that you are TDC on compression stroke?In: timing controlled distributor install question.
3 years ago
Beautiful cars. Thanks for sharing!!!!
AustinIn: 1958 Lister race car and 1934 Mercedes-Benz tribute each with small-block Chevies
3 years ago
That voltage drop is likely your problem the whole time. When the voltage drops below 11, the ecu s …In: New Install, Will not start
3 years ago
No worries on the section. I can always move it.
Cam specs would be helpful.In: Throttle limitation and power loss
3 years ago
Your log is too long. Try editing down to the problem area. I couldn’t get to it without the drive …In: Throttle limitation and power loss
3 years ago
What is your fuel pressure?
Don’t over think it. 99 percent something simple.In: Throttle limitation and power loss
3 years ago
Go to load cal to ecu, or something like that. There will be 3 default tunes, 4 6 or 8 cylinder. L …In: Factory Reset
3 years ago
4 years ago
4 years ago
I agree with above. Disable decel fuel cutoff by setting enable temp to maximum.In: Lean to rich under decel
4 years ago
Delete all the dashboard folders. It will generate a new folder when you datalog.In: fitech 30003 not data logging
4 years ago
4 years ago
I really hoped to film this course. When I figured up the time and cost, it didn’t make financial s …In: Online Fitech Course
4 years ago
This is not uncommon. Couple things you can change. Try this first. Easiest and may solve your is …In: Engine dies when coasting to a stop.
5 years ago
Inline fuel pumps can create issues. They are not the best choice.In: runs fine untill i hit the hiway. settings or setup?
5 years ago
Could be a hot start issue. Fuel is vaporizing on butterflies. Try half throttle for prime shot an …In: Newbie with questions
5 years ago
5 years ago
You most likely have an exhaust leak. Getting fresh air to the sensor causing it to see lean. Engi …In: Afr lean at idle
5 years ago
6 years ago
Quote from camarostricken on March 11, 2020, 8:31 am
so to properly setup the linkage so primarys a …In: Secondary Adjustment
6 years ago
The best place to start is to post a 30 second idle datalog at operating temperature. You must shar …In: possible operator error?
6 years ago
Without seeing the car, I would lean toward grounding issues, if the fan is staying on when key off. …In: spitting back and Its on FIRE!
6 years ago
I didn't see any major issues with your Datalog. Never saw it go lean. Actually pretty stable …In: Car goes lean after putting in gear
6 years ago
Quote from TTA Perf on March 9, 2020, 3:38 pm
Ok, my thinking is wrong.
Start with 25%-30% more …In: My take on tuning with e85
6 years ago
Quote from Sdflanagan07 on March 2, 2020, 6:42 am
I have a 600hp no power added kit and most of the …In: Boosted non pa fitech
6 years ago
What is your AFR trim and AFR Learn when this issue is happening?In: Lean spike at idle and tip in on Warm Engine
6 years ago
Quote from GTRMikie on February 10, 2020, 8:08 am
I have a FiTech in-line fuel pump on my Go Street …In: Which fuel pump?
6 years ago
Quote from Keith Raffel on February 19, 2020, 3:53 pm
I'm running the Go Street 400 with a Com …In: Fuel pressure questions
6 years ago
100 micron before the pump and 10 micron or better after the pump.In: Serviceable Parts and Accessories
6 years ago
You have the latest Software installed.
Cranking has been an issue for many. I still fiddle with …In: Cant get my 30003 to cold start
6 years ago
Quote from Scrogs on February 6, 2020, 3:59 pm
Fixed it. It was the gasket between the ECM and the …In: Bad map sensor
6 years ago
Quote from wkd68 on January 27, 2020, 8:57 pm
did anyone ever provide the k line driver file? i nee …In: K-Line driver
6 years ago
When those values are locked up, it usually means there is some electrical interference. Any codes …In: Bad map sensor
6 years ago
You could have a bad handheld cable or the internal fuse is blown for the handheld. At your own ris …In: GO Street 400 install, Handheld not working
6 years ago
Quote from Peterpimmperle on February 4, 2020, 9:31 pm
have you found the solution anytime?
I ha …In: ecu no response
6 years ago
Simply loading the default V8 calibration and then setting the basics will get you started again.In: 383 in a 55 Chevy
6 years ago